Flush mechanism for Perfect Float cistern with double flush bottom water valve, 3/6 Sanpreis

1. Systems with bottom liner:

• "Float mechanism": This is the most common type of valve, which is considered a guarantee of reliability. How it works: the built-in float rises and falls depending on the water level in the tank, providing precise and silent control of the drain.
• "Membrane mechanism": An innovative choice for those who appreciate modern technologies. The membrane replaces the traditional float and provides reliable control of the water drain, as well as reduces the risk of leaks.
• "Double drain mode": Save water by choosing between full and partial drain. This type of valve gives you control over water consumption and savings on water bills.

2. Systems with side eyeliner: - "Innovative side eyeliner": Modern technologies have made side eyeliner quieter and more efficient. It can be a stylish and functional choice for your toilet bowl.

3. Additional features: - Go to the next level of comfort with fittings offering antibacterial coating for cleanliness and safety, overflow protection systems to prevent accidents, as well as adjustment of the flush force to adjust to your needs.

The choice of fittings for the drain tank is not only a matter of convenience, but also an important economic and environmental decision. We offer a wide selection of toilet fittings to meet all your requirements and provide you with quality, reliability and water savings. Our products meet the highest standards, and your comfort is our top priority. Buy with confidence in Budlea!

The choice of fittings for the toilet is not just a task, it is the key to the reliable and efficient operation of your sanitary device. We are ready to share with you a few important steps that will help you make the right choice:

• Toilet Bowl Manufacturer and Model: Start by studying the manufacturer and model of your toilet bowl. This information is the starting point for the selection of compatible fittings. Not all fittings are suitable for all toilet bowls, so precision is your best ally here.
• Method of water supply: Decide how water is supplied to the tank of your toilet bowl - from below or from the side. This is an important point, since the fittings must correspond to this method of supply.
• Water supply system: Make sure which water supply system you have at home - pressure or non-pressure. This affects the way the valve works, so choose the one that is right for your system.
• Design features of existing fittings: Pay attention to the features of your current fittings, such as the type of membrane or float. This will help you choose the fitting that best suits your requirements.
• Adjustable flush volume: If it is important to be able to adjust the flush volume, then make sure that the selected valve provides this function.
• Flush control method: Consider which flush control method is more convenient for you - a drain button or another mechanism. Your comfort is an important aspect of the choice.
• Consultation with professionals: If you have any doubts or questions, do not hesitate to contact professionals in plumbing stores. They will be happy to help you make the right choice, taking into account all your needs and peculiarities.

And don't forget about the budget and additional features that may come in handy. We provide a wide selection of toilet fittings to meet all your needs. We are sure that the right fittings will make your toilet reliable and efficient, and the choice of Budlea is your right decision!

The toilet is one of the most important sanitary devices in your home. And, like any other equipment, fittings in the toilet are subject to wear and aging over time. Our experts will tell you when to pay attention to the condition of the toilet fittings and think about replacing it.

• Loss of functionality: If your toilet does not perform its functions properly, this can lead to inconveniences and unpleasant surprises. For example, fittings may stop completely filling the tank with water after flushing, which reduces the efficiency of flushing, or do not stop draining water after flushing, which can cause overflow.
• Frequent leaks: Leaks from the toilet tank can be a serious problem. If you often have leaks, this may be a sign of wear or damage to the fittings. Not only does this increase water consumption, but it can also cause damage to the floor and walls. 3
• Noise and vibrations: Old fittings can become a source of unpleasant noise and vibrations when filling the tank with water. This not only interferes with your comfort, but can also disturb other family members. Replacing with new fittings can eliminate this problem and make the use of the toilet quieter.
• Aging and wear: Even if the valve does not fail, it is subject to wear over time. The average service life of the valve is about 150,000 cycles, but this may vary depending on the quality and manufacturer. If your fittings are older than 5 years and begin to show signs of wear, consider replacing them to avoid problems in the future.
• Efficiency Improvement: Modern fittings offer many features that can improve the efficiency and economy of your toilet bowl. Adjustable flush, water saving and other functions can help save water and reduce water supply costs.

The general rule is that if you have any problems with the toilet fittings or it is no longer young, it is worth considering a replacement. Replacing fittings usually does not take much time and can significantly improve the functionality and reliability of your toilet.

In the Budlea online store, we offer a wide selection of modern toilet fittings to meet all your needs and provide you with reliable and efficient sanitary equipment. Be attentive to the condition of your fittings and keep its reliability under control - this is a guarantee of comfortable and economical operation of your toilet.

Toilet drain mechanisms are an important part of sanitary equipment that determines the efficiency of water use and the level of savings. When choosing a drain mechanism for your toilet, it is important to take into account various parameters and needs. Let's consider two main types of drain mechanisms: single-mode and dual-mode.

Single-mode drain mechanisms: Single-mode drain mechanisms have a fixed volume of water that is used for each flush. This is usually about 6-9 liters of water. This type of mechanism is easy to use and maintain, and it can be found in older toilets and less modern models. However, it is not always economical in terms of water consumption, as it uses a large volume even for small flushes. This can affect your water supply costs and harm the environment due to excessive consumption of water resources.

Dual-mode drain mechanisms: Dual-mode drain mechanisms provide users with two flush options: full flush and partial flush. A full flush is used to remove larger volumes of waste and usually corresponds to a single-mode flush (6-9 liters). Partial flush, on the other hand, is designed to flush smaller volumes and usually uses about 3-4 liters of water. This type of drain mechanisms is considered more economical, as it allows you to choose the volume of water depending on the need. It helps to reduce water consumption and reduce water bills.

When choosing a drain mechanism for your toilet, several important factors should be taken into account:

• Water saving: If it is important for you to reduce water consumption and reduce water supply costs, then a dual-mode drain mechanism with a partial flush option will be a more economical option.
• Budget: Single-mode mechanisms are often more affordable in terms of cost, but keep in mind that in the long term they can lead to additional water costs.
• Environmental considerations: If it is important to reduce your ecological footprint and contribute to the conservation of water resources, choosing a dual-mode mechanism will be a more sustainable solution.
• Toilet Bowl Compatibility: Make sure that the selected drain mechanism is compatible with your toilet bowl and does not require major design changes.

Depending on your needs and priorities, the choice of a drain mechanism can significantly affect your comfort, economy and respect for the environment. In the Budlea online store, we offer a variety of toilet drain mechanisms to help you choose the best option that meets your needs and expectations.

The float in the toilet tank plays a key role in adjusting the water level and the proper operation of the drain mechanism. However, like any other piece of plumbing equipment, it can run into problems that can lead to water leakage or improper operation. In this article, we will look at the common reasons why the float may not hold water in the toilet tank, and how to eliminate them.

• Float depressurization: Float depressurization is one of the most common reasons why it ceases to perform its function correctly. If the float has a leak or small cracks, water begins to get inside it. This reduces its buoyancy, and it stops floating to close the drain valve. As a result, water is constantly flowing into the toilet, which can lead to water loss and an increase in water bills. The solution to this problem is to replace the damaged float with a new one.
• Valve or gasket malfunction: The shut-off valve inside the float may become damaged or wear out over time. Also, the gasket between the valve and the tank may lose its tightness. As a result, water can penetrate through these defects, which leads to uncontrolled draining. Check the condition of the valve and gaskets, and replace them if necessary.
• Problems with fixing the float: Fixing the float to the drain mechanism or tank can also be the cause of improper operation. Over time, the bolts and nuts may loosen, and the float ceases to perform its functions correctly. Check the mounting condition and, if necessary, revise it to ensure that the float is securely attached.
• The float gets stuck: Sometimes the float can get stuck inside the tank due to incorrect installation or wear of the mechanism elements. This may prevent it from performing its function correctly. Make sure that the float moves freely inside the tank and does not get stuck on any obstacles.
• The water in the tank is too low or high: If the water level in the toilet tank is outside the optimal parameters, the float may not have sufficient buoyancy or a place to float. Make sure that the water level is in accordance with the recommendations of the toilet bowl manufacturer.

Depending on the nature of the problem and its complexity, you can try to fix it yourself or contact a professional plumber for a more detailed diagnosis and repair. In any case, timely detection and elimination of problems with the float will help save water and prevent leakage.

Before proceeding to the selection and installation, let's figure out exactly how the toilet shut-off valve functions. The principle of its operation is simple and effective:

• Water supply: When you press the flush button or lift the toilet lever, water from the plumbing begins to flow into the toilet bowl drain tank.
• Rising float: There is a float inside the tank that "floats" in the water. As the tank is filled with water, the float rises.
• Shut-off valve: The float rises to the level previously set for flushing. When the float reaches this level, it exerts pressure on the lever, which, in turn, acts on the shut-off valve.
• Blocking the water supply: Under the influence of the float and lever, the shut-off valve closes, stopping the flow of water from the water pipe into the toilet tank.
• Flushing: After the shut-off valve is closed, the water in the tank begins to flush the contents of the toilet bowl into the sewer through the drain ladder.
• Flushing completion: When the tank is completely empty, the float is also lowered, opening the shut-off valve and allowing water to flow back into the tank. The toilet is ready for the next use.

Choosing the right shut-off valves for your toilet is an important step to ensure its reliable operation. When choosing, pay attention to the following factors:

• Installation type: There are two main types of installation - lower and upper. The lower mounting is installed inside the tank, and the upper one is installed above it. Make sure that the selected fittings match your type of toilet.
• Performance: Shut-off valves differ in flushing performance. Make sure that the selected model is able to provide the required amount of flushing.
• Material quality: Stainless steel and high-strength plastics are the preferred materials for shut-off valves. This guarantees a long service life and reliability.

The correct installation of shut-off valves is a key point in ensuring the smooth operation of your toilet. If you have no experience in plumbing work, it is recommended to contact professionals. However, if you decide to perform the installation yourself, follow the instructions provided by the valve manufacturer.

• Turn off the water supply: Make sure that the water supply to the toilet is turned off before starting work.
• Clean the toilet tank: Thoroughly clean the toilet tank from old fittings and debris.
• Install the valve: Install the shut-off valve according to the manufacturer's instructions, including attaching the valve to the tank and connecting pipes or hoses.
• Adjust the water level: After installation, make sure that the water level in the tank is correctly adjusted to ensure correct flushing.
• Check for leaks: Turn on the water supply and carefully check the valve for leaks.