Perforated TPE tape Hydroflex for waterproofing expansion joints and cracks 200 mm wide, 1.5 mm thick, 5 r.m. Arfen

1 412

uah / roll.

HYDROFLEX waterproofing tape is an elastic material based on thermoplastic elastomer (TEP). The membrane is designed for waterproofing expansion joints and cracks in buildings, as well as for waterproofing basements, underground structures, tunnels, vents, hydraulic structures and swimming pools.A specially developed formula allows for high adhesion to both dry and wet concrete surfaces. The HYDROFLEX membrane is resistant to the effects of the root system of plants and aggressive substances of the chemical industry (fuel oil and technical oils). The HYDROFLEX membrane is available with perforation at the edges of the membrane, 1 and 2 mm thick in rolls of 5 meters, 150, 200, 250, 300 and 400 mm wide.

Application:expansion joints in floors, ceilings, walls

expansion joints separating free-standing sections of buildings
when arranging expansion joints in conjunction with the profile systems of TM "ARFEN"
cold and working seams
joints of precast concrete structures

Advantages:the system is resistant to positive and negative pressure

possibility of laying on wet surfaces
high chemical resistance
wear resistance
does not require additional mechanical fastening at the edges
operating ambient temperature from -40From up to 90C
compatible with bitumen
resistance to UV radiation (used on high-rise construction sites)

Hydroflex thermoplastic tape with high elasticity is used for sealing expansion joints and cracks. The assortment includes perforated and non-perforated tape, width 150 mm, 200 mm, 250 mm, 300 mm, 400 mm, thickness 1 mm and 1.5 mm.

Scope of application:Horizontal and vertical expansion joints.

Underground structures, basements and semi-basements, blind spots.
Hydraulic structures designed for wastewater treatment, reservoirs for drinking and household water and swimming pools.
Tunnels and ventilation openings.
For waterproofing cold joints.

Main advantages:Easy to apply with epoxy glue.

The uniqueness of the chemical composition ensures high elasticity (600%).
High adhesion to dry and wet concrete.
It is not damaged by plant roots.
Resistance to aggressive effects of ozone, fuel oil and oil.
Adaptation to use in a wide temperature range.
The possibility of connecting two bands by means of thermal exposure.

Epoxy glue:Hydroflex-21 is a solvent-free epoxy two-component adhesive.

Designed for fixing deformation tapes.

Appointment:Fixes the deformation tape

Fasteners of reinforcing outlets and bolts
Installation of guide machines and cranes to the base

Advantages:High adhesion ability

Chemical resistance
Absence of solvents in the composition
It is used for deformation joints of floors, walls, blind areas and terraces
Waterproof and gas tightness
Adaptation to wet surfaces
A practical consistency for application
Applied without primer
Multi-colored components help to monitor whether the mixture is well mixed enough.

Chemical composition : TEP (thermoplastics)

Colour : Light grey

Shore hardness : A 80

Operating temperature : -40/ 90

Heater temperature : 270 C

Elongation to failure : 600%

Tensile strength : N/cm >600 N/cm

Resistance to hydraulic pressure bar : >8 bar

Tensile strength : MPa >6 MPa

UV resistance : 7500 h

Bitumen resistance : Good

Resistance to sulfuric acid : Good

Alcohol resistance : Good

Detergent resistance : Good

What to pay attention to when preparing a mixture?

1. The mixture is prepared immediately before use and should be used within 30 minutes.

2. Do not leave the mixture in the container for more than 5 minutes after the end of mixing.

3. During application, the temperature of the substrate and the environment should be within 5 - 30 °C.

The lifetime and processing time of artificial resins depends on the humidity of the base and the ambient temperature: at low temperatures, the lifetime of the finished composition increases, and on the contrary, high temperatures accelerate the reaction

What is the consumption of Hydroflex - 21?

Consumption: Hydroflex 21 - 1.6 kg / 1 sq.m. per 1 mm layer, the specified material consumption rate is designed for a flat surface and a temperature from 15 to 25 ° C. At lower base temperatures, the flow rate may increase and the curing time may increase.

Unfortunately there are no reviews yet. But you can fix it!