Online shop "Budleya"
Useful articles
Bathroom and plumbing
Toilet installation installation: simple and clear instructions

News

Toilet installation installation: simple and clear instructions

Everyone wants a modern bathroom that will be visually spacious with a modern interior and cool plumbing. But, meeting on the way to your dream such words as "suspended toilet", "installation of concealed installation", a slight panic begins. After all, at first glance, this is a miracle device and you need to spend a lot of money on it, so you also need to pay the master. But everything is not as scary and difficult as it seems, and in this article I will tell you in simple words, "How to install a toilet installation yourself."

The installation for the toilet bowl is a metal frame with a drain tank. The volume of such a tank is not less than that of a regular toilet. It is the main element of the design. All this mechanism should be hidden in a niche of the wall, so the installation needs to be attached, and then make a metal frame sheathed with sheets of drywall. It's not difficult, but at the same time it can withstand tiles and even shelves on such a wall. The visible part in such a partition will be only the drain button.

Installation of such an installation can be carried out to any walls, both capital and partitions with GC. It can also be placed in a corner, under windows, etc. Due to the fact that the installation has 2 mounting points in the floor and walls.

Also in the kit you can find schematic installation instructions. Also included are all the small elements, without which it is impossible to perform installation, these are: studs and nuts for fixing the toilet, adapters for connecting to the toilet and sewer, plugs for cladding work, etc.

We will need:

Drill with drills on concrete
Tape measure and pencil
Screwdriver (if not, screwdriver)
Silicone sealant
FUM Feed
Level

Well, let's start the installation! Make sure that all the components of the installation are in place. A silicone sealant is also needed to seal the joints. And to seal the threaded connections, you will need a FUM tape.

MarkupIn order to make a markup, you need to take a pencil or a black marker, as well as a tape measure and a construction level.

First you need to determine the location of the central axis of the structure to perform the marking there. To do this, you need to draw a straight line in the center of the frame. You also need to outline the outline of the drain tank with a pencil on the wall. And then make a marking on the wall and floor for fasteners. After all the markup is done, it is better to check its correctness again, if everything is correct, you can proceed to the installation.

MountingBefore starting the installation, be sure to turn off the water!

On the floor and wall, according to the marking, you need to make holes with a puncher or drill. To place dowels in them for greater reliability, you can fix the frame frame with anchor bolts. In this case, the installation frame must be set using the level. The height of the installation can be adjusted as you need with the help of extendable legs.

Pipe connectionAfter installation of the installation, the outlet in the drain tank must be connected to the water supply system.

You need to do this with a plastic pipe. Further down, using the pipe, the installation must be connected to the sewer pipe.

After that, the system needs to be tested for tightness, the rate of water discharge and the overall correctness of operation. To do this, you need to connect the toilet bowl for a while. It is attached to the installation using special pins (included). It will also make it possible to check the operation of the drain button. If no problems are detected, the toilet bowl must be securely fixed. This is followed by the lining of the structure.

To prevent dirt and dust from getting into the installation tank, you need to close the mounting "window", or you can put on a special plug.Covering of the structure

To arrange a false system, you will need a metal profile, it is installed around the perimeter of the installation.

This will be a reliable solution, it can easily be sheathed with GC or fiberboard. When covering, you should have a hole for installing the drain key. After that, the cladding works are performed and the drain button is installed.

Ready! You can open the water supply and check the operation of the system.

Let's summarize the resultsFirstly, the installation for a suspended toilet is a modern solution.

Secondly, you save space and simplify the cleaning process for yourself.
Thirdly, such a solution is not much more expensive than installing a conventional outdoor toilet with a tank.

I hope that my short and simple instructions were useful to you.