Product code: 100005124
Penetrating waterproofing compound Teknomer 100, 20kg TEKNO
Tecpomeg 100 is a crystallized one-component waterproofing material based on cement. Gives surfaces resistance to negative and positive water pressure. The insoluble crystals included in the material fill the pores of the concrete, preventing the penetration of water.
Where it is used:
- tunnels and elevator shafts
- basement floors and basements
- showers and bathrooms
- pools, wells and water tanks
- reinforced concrete pipes
- large engineering structures.
Advantages:
- penetrates deeply into concrete foundations
- resistant to negative and positive water pressure
- it can be applied manually or by spray.
Instructions for use:The surface for application must be cleaned of any types of oil, rust, detergents and other substances that prevent setting.
If there are areas in the form of cracks, cavities on the surface - they should be repaired with the help of convenient cement mixtures Teknorep 300 and Teknorep 300 EX.
* If the insulated surface is dry, it should be moistened. If there is an active leak, it must be eliminated by the Teknoplug material.Add 6-7 liters of water to a clean container and gradually pour Teknomer 100 into it, while stirring at low speed using a low-speed mixer, until a homogeneous mass is obtained.
The mixing time should be at least 5 minutes, then leave the solution alone for 3 minutes, and mix again for 2 minutes.
1. Brush applicationThe prepared mixture is applied to the surface with a brush in 2-3 layers.
The layers should be applied perpendicular to each other.
The waiting time between layers is maintained so that the previous layer does not stick to the fingers.
2. SprayingTeknomer 100 is sprayed onto the prepared surface in a uniform layer.
* To use Teknomer 100 as an additive for concrete, it is necessary to pre-mix the solution, then add Teknomer 100 to the total volume of the mixture and mix additionally for 5-7 minutes.
Application Notes/Limitations:
- Do not use on surfaces made of wood, chipboard, MDF, plywood, PVC and metal
- Use gloves, mask and glasses during the work
- Use the recommended mixing proportions
- After applying the solution, the surface must be protected from adverse weather conditions, such as direct sunlight, strong wind, high air temperature (above 35 °C), rain and frost.
- The tools and equipment used must be washed with warm water immediately after use.
|
Colour |
Gray |
|
Expiration date |
12 months in a dry environment in a closed package |
|
Packaging |
20 kg bag |
|
Application temperature |
( +5°C) - ( +35°C) |
|
Mixture ratio |
6-7 l of water / 20 kg of powder |
|
Life time of the mixture |
20 min |
|
Full cure |
5 days |
|
Water resistance |
7 Bar (positive and negative) |
What is penetrating waterproofing?
Penetrating waterproofing provides reliable water resistance of concrete structures. Penetrating materials can be used both at the initial stage of construction, and in the future during the repair and restoration of water resistance of building structures. One of these materials is Teknomer 100. It is a crystallized one-component waterproofing material based on cement, which gives the surfaces resistance to negative and positive water pressure.
How does penetrating waterproofing work?
The principle of operation of penetrating waterproofing for concrete is its duality. On the one hand, we carry out waterproofing of the concrete surface, on the other — the pores inside the concrete crystallize due to penetrating substances and ensure its water resistance.
One of such materials is Teknomer 100. The insoluble crystals included in the material fill the pores of the concrete, preventing the penetration of water and making it waterproof
On which surfaces can penetrating waterproofing be applied?
It is important to take into account that penetrating waterproofing can only be used on concrete or reinforced concrete surfaces. For brick and stone foundations, a different method of protection against moisture penetration should be used. Teknomer 100 penetrating waterproofing is a crystallized cement–based material. The crystals included in its composition penetrate deep into the pores of concrete, making it not waterproof.
How to apply penetrating waterproofing?
The penetrating waterproofing of Teknomer 100 must be applied to the cleaned surface. Immediately before applying waterproofing, it is necessary to moisten the surface very well with ordinary clean water. You can apply the material with a rigid brush or spray in 2-3 layers, where each next layer must be applied perpendicular to the previous one.
How to waterproof the walls inside the basement?
In order to waterproofing the walls inside the basement, it is best to use Teknomer 100 penetrating waterproofing, which protects the concrete surface from positive and negative water pressure. The insoluble crystals included in the material fill the pores of the concrete, preventing the penetration of water.
Other products in the category
Useful articles
