Cement-based Teknofay C1T ceramic tile adhesive, grey, 25 kg TEKNO

285

uah / bag

Teknofay C1T is a cement-based adhesive solution for ceramic tiles with high adhesion strength.

Where it is used:

In residential buildings, shopping malls, administrative buildings, hospitals
It is used on vertical and horizontal surfaces
For gluing materials with low adhesion, such as small and medium-sized tiles, ceramics with a degree of water absorption of more than 3%.

Features and Benefits:

Easy to prepare and apply
It has high adhesive properties
Does not slip in an upright position

Instructions for use:

Pour 6,8-7,2 liters of clean, transparent water into a clean container, in which there are no all kinds of materials that prevent adhesion. After that, slowly pour Teknofay into a container filled with water. Mix the material with a low-speed mixer until a homogeneous mixture without lumps is obtained. The mixture obtained as a result of mixing should be left alone for 3 minutes and stir it again for 2 minutes until it becomes homogeneous.

Application Notes/Restrictions:

The product may irritate the skin. When working with the material, it is necessary to use work clothes, protective gloves, a mask and glasses.
The prepared solution is applied to the surface with a toothed spatula with the appropriate size of the teeth.
The tile is laid on the glue and pressed no later than 10 minutes after its application.
The position of the tile can be adjusted within about 15 minutes after laying.
In case of contact with the adhesive solution in the eyes, rinse immediately with warm water and consult a doctor.
It is recommended to fill the facing seams with grout no earlier than 24 hours after laying the tile.
The work should be carried out in dry conditions, at air and base temperatures from +5°C to +30°C and relative humidity not higher than 80%.

Name of the indicator	Normative value
Appearance	Grey Powder
Storage in a dry dark warehouse, subject to the temperature range of +5... +35 ° C, humidity not higher than 80%	12 months
Packaging	25 kg bag
Temperature range of application, °C	+5°С...+35°С
Mixing proportions	6.0 - 7.0 water / 25 kg powder
Life time of the mixture	6 hours
Operating temperature range	-40°C...+80°C
Resistance to sliding	≤ 0.5 mm
The beginning of mechanical loads	1 day - on the floor, 8 hours - on the wall
Adhesive joint strength:

After exposure in a dry environment	≥ 0.5 N/mm²
After exposure in a wet environment	≥ 05 N/mm²
After exposure in a hot environment	≥ 0.5 N/mm²
After cyclic freezing and thawing	≥ 0.5 N/mm²
Fire reaction class	A1

CONSUMPTION TABLE

TEKNOFAY	Density of the mixture (g/l)	Powder consumption per 1 m² (kg)	Amount of water for mixing, l
25 kg bag	~ 1.80	3 - 5	6,0 - 7,0

Adhesive for ceramic tiles Teknofay

How to choose the right adhesive for porcelain stoneware?

It is recommended to choose tile adhesive depending on many factors, for example, you need to take into account: the size of the tile, the type of base on which the tile will be laid. You should also pay attention to the lifetime of the mixture and the time of commissioning of the finish coating.

Can tile adhesive be used instead of cement?

Since the characteristics of tile adhesive are better from cement mortar, the answer is definitely positive. Tile adhesive is very often used to seal small chips and small cracks in walls. They can also be used to close the gates when introducing hidden wiring.

How to apply tile adhesive to the surface?

To apply the adhesive solution, use a flat spatula. After applying the glue, the toothed side of the spatula should be passed over the surface and the tile should be pressed tightly. The tile surface must be in contact with the glue by at least 80%. After the glue is applied, you have 15 minutes to lay and level the tile, so it is not recommended to apply the composition immediately on the entire plane. It is better to carry out the work gradually.

Unfortunately there are no reviews yet. But you can fix it!