Sealant one-component acrylic window Profflex B, white, for indoor use, 5 kg Tenax

700

uah / bucket

PROFFLEX B is a one–component acrylate sealant with high vapor barrier properties. The sealant is designed to perform the inner layer of the mounting seam in accordance with DSTU-N B V.2.6-146:2010 with an allowable deformation of the mounting seam of no more than 15% for sealing the inner contour of window, door and balcony structures.

Features:High vapor barrier properties

Very good adhesion to most building materials
Protects against penetration of water vapor from residential premises deep into the mounting seam
Ready to use
Resistance to deformation
Durability
Possibility of application at negative temperature
Possible surface coloring
Due to its high thixotropy, the sealant can be applied to horizontal and vertical, inclined surfaces.
Appearance – paste

Profflex B is a one-component sealant with high vapor permeability on an acrylic base. The sealant is designed to seal the inner contour of window, door and balcony structures, with an allowable deformation of the mounting seam of no more than 15%.

Color - White
Type - Single-Component
Water Resistance - Moisture Resistant
Density - 1608 kg/m3
Consumption - 120 g/m.p.
Volume - 5 kg
The country of origin of the product is Latvia
Warranty - 12 months

Scope of application:Sealing of plastic, aluminum and wooden frames

Sealing of door frames and window openings

Consistency - Thixotropic paste
The base is Polyacrylate
Solidification - Evaporation of water
Vapor permeability resistance, (m2·h·Pa)/mg, - no more than 0,23
The formation time of the surface film, g. - 1 hour (at 23 ° C and normal humidity)
Curing time at a layer thickness of 3 mm. - 48 hours (at 23 ° C and normal humidity)*
Density, not less than kg/m - 31608 kg/m3
The recommended application temperature range is from 5 °C to 35 °, (the minimum ambient temperature during application is up to -20 °C and relative humidity is not more than 90%). The minimum temperature of the product for application is 13 °C
Operating temperature range - From – 400C to 800C
Adhesive strength, MPa, not less:
- PVC - 0.22
- tree - 0.43
- metal - 0.24
- concrete - 0.65
Water resistance at a pressure of 600 Pa, hours, - at least 24 hours
Yield strength, mm by 2 mm thickness, - no more than 0
The limit of adhesion strength, MPa, is not less than 1.0
Resistance to deformation, %, - not less than 15
Elongation at the moment of rupture % - not less than 364%
Color - white
Stability during freezing/defrosting - 10 cycles
The projected service life of conditional years is at least 20
* With a decrease in temperature or an increase in humidity, the time increases

How to prepare the surface for sealant application?

The sealant is completely ready for use. Before use, the surface should be degreased, cleaned of dirt, dust, loose particles. The edges and surfaces of openings should not have chips, sinks, concrete mortar flows and other damages with a height (depth) of more than 10 mm. Defective places should be plastered with waterproof mixtures. Loose, crumbling areas of the opening surfaces should be reinforced (treated with astringent mixtures or special film materials. It is possible to apply the sealant on a dry and wet surface. The presence of droplet moisture on the surface is unacceptable. When working in winter, clean the surface from snow, ice, etc.). It is unacceptable to apply sealant during precipitation (rain and snow).

How to apply sealant?

The sealant is applied to the prepared surface with a spatula or paint brush. The recommended thickness of the application layer is from 3.5 to 5.5 mm. The ambient temperature when applying the sealant is from -20 ° C to 35 ° C and the relative humidity is not more than 90%. When laying the sealant, it is recommended to protect the front edges of the structures with masking tape in order to prevent their contamination. The masking tape must be removed before the formation of a surface film on the sealant.

Unfortunately there are no reviews yet. But you can fix it!