Thixotropic adhesive for ceramics and granite Teknofay Rapid fast-hardening, gray, 25 kg TEKNO

474

uah / bag

Teknofay Rapid C1FT adhesive is a fast-hardening, highly effective, elastic cement-based adhesive solution with zero vertical sliding.

It is used for laying tiles, mosaics, porcelain stoneware and natural stone of large and extra-large format:

Floor, walls and ceiling
Gypsum plaster, gypsum panels, aerated concrete and open concrete
It is used for gluing ceramics, porcelain stoneware, natural stone, etc.
Ideal for use in places that need to be put into operation during the day
When gluing tiles with increased water absorption (for example, some types of natural stone or hand-molded clinker tiles)

Features and Benefits:

The surface is ready for pedestrian loads in 3-5 hours after laying the tiles
Grouting of seams after 4 hours
Thixotropic (prevents heavy tiles from sliding on vertical and inclined surfaces)
Easy to prepare and apply
Resistant to water, moisture

Instructions for use:

Surface preparation: the surface must be clean, smooth, firm, and even.
The surface should be cleaned of dust and dirt, and damaged areas should be repaired with TEKNOREP. There should be no oil, dirt and rust residues on the surface.
If the solution is to be applied to marble, ceramics or a slab, the surface should be roughened. The concrete floor needs to be moistened, but so that there are no puddles on the surface.

Mixing: Pour 6.0-7.5 liters of water into a clean container in which there are no residues of materials that prevent adhesion. Teknofay Rapid is delivered in bags of 25 kg in powder form, the powder is added to a container with water. The solution is mixed with a mixer at low speeds until a homogeneous mixture without lumps is obtained. The mixing time is at least 5 minutes. Leave the solution obtained at the end of the process alone for 3 minutes, then mix it again for 2 minutes until it becomes homogeneous.

Application: The tile cleaned of dirt (moisten, if necessary, clean from dust) should be laid on the applied solution for 15 minutes (until the solution sets on the surface) and pressed to ensure good contact with the glue (preferably pressed using a rubber hammer).

Restrictions and special conditions:

The product may cause irritation if it gets on the skin. Work clothes, protective gloves, mask and glasses should be used. A protective cream can be applied to the hand before starting work. If the solution gets into your eyes, immediately rinse your eyes with warm water and consult a doctor.
If the ambient temperature is below +5°C, it is necessary to protect the surface from frost.
At temperatures above +35°C, the surface must be protected from sudden loss of water. 24 hours after applying Teknofay Rapid, the sealing of the seams should begin.
Do not add foreign substances.
After application, it is necessary to protect the surface from adverse weather conditions, such as direct sunlight, strong wind, high air temperature over +35°C, rain and frost. Cleaning should be carried out with water before Teknofay Rapid completely hardens. Immediately after application, wash your hands and face thoroughly with warm water and soap.
The equipment should be rinsed with water immediately after application before the solution hardens.

Packaging and storage:

Store in the closed original packaging in a cool and dry place, protected from freezing.

The name of the indicator	Normative value
Appearance	Grey Powder
Storage in a dry dark warehouse, subject to the temperature range of +5...+35 °C, humidity not higher than 80%	12 months
Packaging	25 kg bag
Temperature range of application, °C	+5°С...+35°С
Mixing proportions	6.0 - 7.0 water / 25 kg powder
Life time of the mixture	45 minutes
Operating temperature range	-40°C...+80°C
Resistance to sliding	≤ 0.5 mm
The beginning of mechanical loads	1 day - on the floor, 8 hours - on the wall
Adhesive joint strength:
After exposure in a dry environment	≥ 1.0 N/mm²
After exposure in a wet environment	≥ 1.0 N/mm²
After exposure in a hot environment	≥ 1.0 N/mm²
After cyclic freezing and thawing	≥ 1.0 N/mm²
Flexibility (EN 12002)	≥ 2.5 mm - S1 flexible
Fire reaction class	A1